Embrizo

How to make an in-the-hoop coaster

Make in-the-hoop coasters with a name or monogram: cork, felt or vinyl, the four color stops, attaching the back, trimming, and a maker that builds the file.

Updated · 7 min read

Four in-the-hoop coasters with names and initials on cork, felt and vinyl, one under a coffee mug
In-the-hoop key fob maker screenshotFree previewIn-the-hoop key fob makerMake an in-the-hoop key fob, bookmark, gift tag or ornament with a name: placement line, tack-down, name and satin border in one file.Open the tool

An in-the-hoop (ITH) coaster is made entirely by the embroidery machine: it stitches the outline, holds the fabric down, adds a name or monogram and finishes the edge with a satin border through the front and the back. There's no sewing machine and no turning. It takes about 15 minutes, and a set of four is a quick housewarming, wedding or hostess gift.

This guide walks through materials and each step. The in-the-hoop maker builds the whole coaster file with your lettering: placement line, tack-down, name and satin border, ready for your machine.

What you need

ItemWhat to useNotes
Hoop4×4 in (100 × 100 mm) or largerA 3.5 in coaster fits a 4×4; a 6×10 fits two
StabilizerMedium tear-awayCut-away under quilted cotton
Front and backCork sheet (2–3 mm), marine vinyl, felt or cotton with battingAbout 4.5 in square each
Needle75/11 sharpA fresh needle for cork and vinyl
ThreadTop and bobbin in the border colorThe back shows, so the bobbin should match
FinishingTape, small curved scissorsA rotary cutter for cutting pieces to size

Cork and vinyl wipe clean and don't soak up a wet glass, so they make the most practical coasters. Felt is the easiest to start with and looks cozy, but it absorbs drips. A quilted cotton coaster with a layer of cotton batting in between is soft and washable.

Making the coaster, color stop by color stop

  1. Placement line: hoop the stabilizer only, drum tight, and stitch the first color: a running outline that shows where the front piece goes.
  2. Tack-down: lay the front piece over the outline so it covers it on every side, tape the corners, and stitch the second color. Take the hoop off the machine (don't unhoop) and trim the front piece close to the tack-down.
  3. Name or monogram: stitch the lettering. Keep it at least 5 mm tall for small lines; a monogram or a short name can fill most of the coaster.
  4. Attach the back: take the hoop off again, tape the backing piece under the hoop so it covers the whole outline, and put the hoop back.
  5. Satin border: stitch the last color through the front, the stabilizer and the back. Tear the stabilizer away and trim the back close to the satin.

Let the hoop sit flat on the machine bed while the border stitches: a hoop that lifts or drags makes the satin wander off the edge. On cork, slow the machine to about 600 stitches per minute.

Try it with your own design

Sign up free, upload an image and get a stitch preview in under a minute.

Drop your image here

PNG, JPG, SVG, PDF or AI · stays on your device

Not sure what to expect? See real examples or how it works.

Coaster sizes and hoops

CoasterSizeHoop
Square or rounded square3.5–4 in (88–100 mm)4×4
Round3.5–4 in across4×4
Mug rug (coaster plus a cookie)5 × 7 in or 6 × 8 in5×7 or 6×10
Set of two at onceTwo 3.5 in coasters6×10, one above the other

A 4×4 hoop's sewing field is about 100 × 100 mm, so a 3.5 in (88 mm) coaster leaves room for the satin border to stitch without touching the hoop. The maker's coaster is 88 mm square with rounded corners.

What to put on a coaster

  • A family name or initial for a housewarming set: the last name on one, the initial on the others.
  • The couple's initials and the wedding date for a wedding or anniversary gift; see the anniversary maker.
  • A single monogram letter in a classic or script font: the monogram maker or the three-letter monogram page.
  • Holiday sets: a snowflake, a holly sprig or a pumpkin from the free designs, one per coaster.
  • Business coasters for a café or a brewery: a simple logo with one or two colors, made with the logo digitizer.

Mistakes that make coasters curl or look homemade

  • A dense fill in the middle: a big filled shape pulls the fabric in and makes the coaster cup. Use satin lettering or a light fill on coasters.
  • Hooping the cork or vinyl: it leaves a permanent hoop mark. Hoop the stabilizer only and lay the fabric on top.
  • A narrow border: a satin narrower than about 3 mm lets the cut edge peek out. The maker's border is 3.5 mm wide.
  • A mismatched bobbin: the back of a coaster is on show every time it's picked up.
  • Trimming after the border instead of before: trim the front close to the tack-down before the lettering, so the border covers a clean edge.

Practice on a free design

167 ready-to-sew designs in every machine format, free with an account.

  • Cherries embroidery design
  • Graduation cap embroidery design
  • Mountains embroidery design
  • Menorah embroidery design
Browse free designs

Selling coasters

Coasters sell well as sets of four, in a kraft box or tied with twine. Cork with a family name or a monogram is the steady seller; wedding sets with initials and a date sell in spring and summer, and holiday sets from October. Material costs per coaster are small, so price by the set and by the time it takes: the embroidery pricing calculator works it out with your hourly rate.

Free account

Put this guide into practice

Create a free account to digitize any image, try every setting and watch it sew. Choose a plan only when you want to download files.

  • Digitize and preview any image
  • Realistic stitch preview and sew-out
  • Download free ready-made designs
  • No credit card needed
FAQ

Questions

The quickest way to see what it does with your artwork is to try it. With a free account, digitizing and previewing cost nothing and take about a minute.

What size is an in-the-hoop coaster?

About 3.5–4 in (88–100 mm) square or round, which fits a 4×4 hoop. A mug rug, a larger coaster with room for a cookie, is about 5 × 7 in.

What is the best material for embroidered coasters?

Cork and marine vinyl: they wipe clean and don't soak up drips. Felt is the easiest to start with but absorbs moisture; quilted cotton with batting is soft and washable.

Can you machine wash embroidered coasters?

Quilted cotton and felt coasters can go in a cool, gentle wash and lie flat to dry. Wipe cork and vinyl coasters with a damp cloth instead.

Why does my coaster curl?

Usually a dense fill in the middle pulling the fabric in, or a stabilizer that's too light. Use satin lettering or a light fill, and a medium tear-away or cut-away stabilizer hooped drum tight.

Can I make four coasters at once?

In a large enough hoop. A 6×10 hoop fits two 3.5 in coasters, one above the other; an 8×12 fits four. Stitch them as one file with the stops in the same order.

Keep reading

Related tools and guides

Your design, ready to stitch

Sign up free, upload an image and see it stitched in under a minute. Your image stays on your device.